ANVIL PIPE SUPPORTS CAD DRAWINGS FULL
ANVIL PIPE SUPPORTS CAD DRAWINGS CODE
ANVIL PIPE SUPPORTS CAD DRAWINGS PLUS

These cookies ensure basic functionalities and security features of the website, anonymously.

Necessary cookies are absolutely essential for the website to function properly.

ANVIL PIPE SUPPORTS CAD DRAWINGS PLUS

It exerts a nominal cold strain force equal to the pre-load force plus the amount of travel from the hot to cold position, times the spring scale of the particular size of the vibration control and sway brace. Under shutdown conditions, the brace allows the pipe to assume its cold position. When correct tension adjustments are completed, the brace exerts no force on the pipe in its operating position. If, with the pipe in its hot position, the tension test collar cannot be turned by hand, loosen the jam nut adjacent to the rod coupling and rotate the coupling until the collar can just be turned by hand. Rod lengths should be cut and final tension of adjustments made for the hot or operating position of the pipe. For pipe sizes 3-1/2 inch and smaller, the small size is recommended for 4 to 8-inch, the medium size and for 10-inch and larger, the large size. To simplify the selection of size, engineers have designed the vibration control and sway brace in three sizes that are readily related to nominal pipe size. When it is possible to calculate the exact restraining force required, the size of the vibration control and sway brace capable of providing this force should be selected. The exact amount of energy needed to control piping should be in proportion to the mass, amplitude of movement, and nature of disturbing forces acting on the pipe. to dampen vibrations, oppose pipe sway and absorb shock forces.

and has initial pre-compressed spring forces from 50 lb.

ANVIL PIPE SUPPORTS CAD DRAWINGS FULL

The vibration control and sway brace gives full deflection forces from 200 lb. ORDERING: Specify figure number, size, description and overall dimension.

ANVIL PIPE SUPPORTS CAD DRAWINGS CODE

SPECIFICATION: Fulfills the requirements of the ASA Code for Pressure Piping as to fabrication details and materials. Enclosed spring excludes dirt and gives a clean, compact appearance.Spring has 3-inch travel in either direction.One spring saves space and simplifies design.A single energy-absorbing pre-loaded spring provides two way action.Vibration is opposed with an instantaneous counter force bringing the pipe back to normal position.The screws in the tension test collar need not be loosened, since they serve only to secure it to the load coupling. If it is not, the sway brace should be adjusted to the neutral position by use of the load coupling. The rod coupling rotates with slight resistance and the tension test collar can be rotated by hand while holding the rod stationary.ĪDJUSTMENT: The sway brace should be in the neutral position when the system is hot and operating, at which time the tension test collar should be hand tight. INSTALLATION: The vibration control and sway brace is shipped ready for installation. SERVICE: Recommended for controlling vibration, absorbing shock loadings guiding or restraining the movement of pipe resulting from thermal expansion bracing a pipe line against sway. SIZE RANGE: For pipe sizes 2 inches through 24 inches. Piping Alignment and Pipe Strain Solutions.Case Study: Engineered Support for Vibration problem.1400 Pipe Shoe Solution for Vibration in Piping Emergency Custom Steel Structure and Support Design and Fabrication.Spring Support and Expansion Joint Audits.Pipe Stress Analysis for Plant Personnel.Pipe Stress Analysis Case Study – Pump Discharge.High Temperature Pipe Supports (Hot Shoes) (HS-1000 – HS-6060).

Cryogenic Pipe Supports (Cold Shoes) (CS-1000 – CS-6080).

Pipe Shields Insulated Pipe Supports (Cold & Hot Shoes) (A1000 – G3000).

Insulated Pipe Supports (Figures 4500-4800).

Note: The application of a load to a structural beam by means of a beam clamp produces a transverse stress, perpendicular to the axis of the beam, in the flange to which the load is applied. Ordering: Specify clamp size, figure number, name, rod size and finish.

Clamps are available, tapped to any specified rod size up to the maximum rod size.

Tie rod insures a tight non-slip fit to the beam.

Quickly, easily, economically installed.

Upper nut is tapped to any specified size up to the maximum rod size.

Installation: Fit jaws over edges of lower beam flange and tighten nuts on tie rod to lock clamp in place. Service: For suspension of heavy loads from beams with flange widths to 15' and flange thickness to 1.031.Īpprovals: Complies with Federal Specification A-A-1192A (Type 28 without links Type 29 with links), WW-H-171-E (Type 30 & 31), ANSI/MSS SP-69 and MSS SP-58 (Type 28 without links Type 29 with links).

Anvil pipe supports cad drawings